Yamaha F300 Page 109 Owner'S Manual Download

Page: 109 / 124

Maintenance

103

Triple engines

EMU29371

Disconnecting the battery

Turn off the battery cut-off switch (if
equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01930]

Disconnect the negative cable(s) from
the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01940]

Disconnect the positive cable(s) and re-
move the battery from the boat.

Clean, maintain, and store the battery
according to the manufacturer’s instruc-
tions.

1. Starboard side engine
2. Center engine
3. Port side engine
4. Red cable
5. Black cable
6. Isolator lead with circuit protection
7. Fuse
8. Battery for starting
9. Battery for accessories
10. Negative connecting cable

ZMU05956

6
7

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F300





























































































































Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands

Yamaha F300, Owner'S Manual

Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands