Yamaha F300 Page 89 Owner'S Manual Download | Manualshive

Page: 89 / 124

background image

Operation

83

unit could be damaged.

●

Do not tilt the outboard motor up so
that the cooling water inlet on the lower
unit is above the surface of the water
when setting up for and cruising in
shallow water. Otherwise severe dam-

age from overheating can result.

EMU35234

Procedure for power trim and tilt models

1.

Place the control lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim
and tilt switch.

WARNING! Using the

power trim and tilt switch on the bot-
tom cowling while the boat is moving
or engine is on could increase the
risk of falling overboard and could
distract the operator, increasing the
risk of collision with another boat or
an obstacle.

[EWM01850]

ZMU06236

N

ZMU05829

N

ZMU06280

UP

ZMU05837

UP

UP

UP

ZMU05838

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
87
88
89
90
91
...
»

Summary of Contents for F300





























































































































Reviews:

No comments

Related manuals for F300

Brand: Yamaha Pages: 20

Brand: fadini Pages: 32

Brand: ECS Pages: 52

Brand: Gigabyte Pages: 125

Brand: Aaeon Pages: 30

Brand: NXP Semiconductors Pages: 269

Brand: MediaQ Pages: 25

VAR-SOM-MX8M-NANO

Brand: Variscite Pages: 2

Brand: Gigabyte Pages: 96

Brand: AOpen Pages: 44

Brand: MSI Pages: 164

Brand: K&B Pages: 6

Brand: BCM Pages: 3

Brand: Texas Instruments Pages: 13

Brand: ECS Pages: 87

Brand: Aaeon Pages: 123

Brand: Gigabyte Pages: 88

Brand: Award Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands