Yamaha F300 Owner'S Manual Download

Page: 20 / 124

Specifications and requirements

EMU35950

Specifications

TIP:

“*” means, select the engine oil referring to
the chart of engine oil paragraph. For further
information, see page 18.

EMU2821C

Dimension:

Overall length:

1029 mm (40.5 in)

Overall width:

633 mm (24.9 in)

Overall height X:

2006 mm (79.0 in)

Overall height U:

2133 mm (84.0 in)

Transom height X:

637 mm (25.1 in)

Transom height U:

764 mm (30.1 in)

Weight (without propeller) X:

365.0 kg (805 lb)

Weight (without propeller) U:

373.0 kg (822 lb)

Performance:

Full throttle operating range:

5000–6000 r/min

Maximum output:

F300TR 220.7 kW@5500 r/min
(300 HP@5500 r/min)
F350TR 257.4 kW@5500 r/min
(350 HP@5500 r/min)
LF300TR 220.7 kW@5500 r/min
(300 HP@5500 r/min)
LF350TR 257.4 kW@5500 r/min
(350 HP@5500 r/min)

Idling speed (in neutral):

650

50 r/min

Engine:

Type:

4-stroke V

Displacement:

5330.0 cm

Bore

stroke:

94.0

96.0 mm (3.70

3.78 in)

Ignition system:

TCI

Spark plug (NGK):

LFR6A-11

Spark plug gap:

1.0–1.1 mm (0.039–0.043 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Electronic fuel injection

Valve clearance (cold engine) IN:

0.17–0.23 mm (0.0067–0.0091 in)

Valve clearance (cold engine) EX:

0.31–0.37 mm (0.0122–0.0146 in)

Min. cold cranking amps (CCA/SAE):

700.0 A

Min. marine cranking amps (MCA/ABYC):

900.0 A

Min. reserve capacity (RC/SAE):

170 minutes

Maximum generator output:

50.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

1.73 (26/15)

Trim and tilt system:

Power trim and tilt

Propeller mark:

F300TR X
F350TR X

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F300





























































































































Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands

Yamaha F300, Owner'S Manual

Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands