Yamaha 2002 FZS600 Supplementary Service Manual Download

Page: 68 / 74

–61–

COOLING SYSTEM

ELEC

6. Thermo unit
7. Coolant temperature warning light
8. Voltage
9. Wiring connections (the entire cooling

system)

Pocket tester:

90890-03112

NOTE:

EB802011

1. Fuses (main, signal and fan)

Remove the fuses.

Connect the pocket tester (

Ω

1) to the

fuses.

Check the fuses for continuity.

Replace the fuse(s).

CONTINUITY

NO CONTINUITY

Open-circuit voltage:

12.8 V or more at 20

EB802012

2. Battery

Check the battery condition.
Refer to “BATTERY INSPECTION” in
CHAPTER 3. (Manual No.: 5DM1-AE1)

Clean the batery terminals.

Recharge or replace the battery.

CORRECT

INCORRECT

EB807010

TROUBLESHOOTING

IF THE FAN MOTOR FAILS TO TURN:
IF THE COOLANT TEMPERTATURE METER FAILS TO MOVE, WHEN THE ENGINE IS WARM:

Procedure

Check:
1. Fuses (main, signal and fan)
2. Battery
3. Main switch
4. Fan motor
5. Thermo switch

Remove the following part(s) before trouble-
shooting.

1) Seat
2) Fuel tank
3) Front cowling assembly

Use the following special tool(s) for trouble-
shooting.

Summary of Contents for 2002 FZS600











































































Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands

Yamaha 2002 FZS600, Supplementary Service Manual

Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands