Yamaha 2002 FZS600 Supplementary Service Manual Download

Page: 32 / 74

–25–

ADJUSTING THE FRONT BRAKE/

REPLACING THE HEADLIGHT BULBS

CHK

ADJ

NOTE:

WARNING

EB304001

CHASSIS

ADJUSTING THE FRONT BRAKE

1. Adjust:

brake lever position
(distance

from the throttle grip to the

brake lever)

a. While pushing the brake lever forward,

turn the adjusting dial

until the brake le-

ver is in the desired position.

Be sure to align the setting on the adjusting
dial with the arrow mark

Position #1

Distance

the

largest.

Position #5

Distance

the

smallest.

After adjusting the brake lever position,
make sure that the pin on the brake lever
holder is firmly inserted in the hole in the
adjusting dial.

ELECTRICAL SYSTEM

EB305051

REPLACING THE HEADLIGHT BULBS

The following procedure applies to both of the
headlight bulbs.
1. Disconnect:

headlight lead

2. Remove:

headlight bulb holder

3. Remove:

headlight bulb

Since the headlight bulb gets extremely
hot, keep flammable products and your
hands away from the bulb until it has
cooled down.

Summary of Contents for 2002 FZS600











































































Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands

Yamaha 2002 FZS600, Supplementary Service Manual

Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands