manualshive.com logo in svg

Yamaha 2002 FZS600, Supplementary Service Manual, Page: 71 / 74

Share
Download
Yamaha 2002 FZS600 Supplementary Service Manual Download Page 71

–64–

COOLING SYSTEM

ELEC

:

Tester (+) lead 

!

 Brown lead 

Tester (–) lead 

!

 Black lead

Thermo unit resistance

80

_

C: 3.4 k

Ω

 

X

 4.0 k

Ω

105

_

C: 1.6 k

Ω

 

X

 1.9 k

Ω

6. Thermo unit

S

Remove the thermo unit from the thermostat
housing.

S

Connect the pocket tester (

Ω

 

 

 1) to the ter-

mo unit 

 as shown.

S

Immerse the thermo unit in a container filled
with coolant 

.

Make sure the hermo unit terminals do not
get wet.

S

Place a thermometer 

 in the coolant.

S

Slowly heat the coolant, and then let it cool to
the specified temperature indicated in the
table.

S

Check the thermo unit for continuity at the
temperatures indicated in the table.

Replace the thermo unit.

GOOD 
CONDITION

BAD CONDITION

7. Coolant temperature warning light

S

Check the LED for continuity.

CONTINUITY

Replace the meter assembly.

NO CONTINUITY

2

8. Voltage

S

Connect the pocket tester (DC 20 V) to the
meter coupler.

S

Turn the main switch to “ON”.

S

Check the voltage (12 V).

The wiring circuit from the main switch to me-
ter coupler is faulty, repair it.

OUT OF SPECIFICATION

1

1

2

NOTE:

Handle the thermo unit with special care.
Never subject the thermo unit to strong
shocks. If the thermo unit is dropped, re-
place it.

WARNING

MEETS
SPECIFICATION

3

EAS00812

Summary of Contents for 2002 FZS600











































































Reviews:

No comments