Yamaha 2002 FZS600 Supplementary Service Manual Download

Page: 60 / 74

–53–

LIGHTING SYSTEM

ELEC

1. Bulb and bulb socket.

Check the bulb and bulb socket for continu-
ity.

Replace the bulb and / or bulb socket.

CONTINUITY

NO CONTINUITY

When the dimmer switch is “LO”.
When the dimmer switch is “HI”.

2. Voltage

Connect the pocket tester (DC 20 V) to the
headlight and high beam indicator light cou-
plers.

Headlight:

Tester (+) lead

Black / Yellow lead

Black / Green lead

Tester (–) lead

Black lead

High beam indicator light:

Tester (+) lead

Black/Yellow lead

Tester (–) lead

Black lead

Turn the main switch to “ON”.

Turn the light switch to “ON”.

Turn the dimmer switch to “LO” or “HI”.

Check the voltage (12 V) of the “Black / Yel-
low”, “Black / Green” and “Black/Yellow”
leads on the bulb socket connector.

The wiring circuit from the main switch to the
bulb socket connector is faulty, repair it.

MEETS
SPECIFICATION

OUT OF SPECIFICATION

Headlight connector

Meter connector

A
B

EB805020

LIGHTING SYSTEM CHECK

1. If the headlight and the high beam indicator

light fail to come on:

Summary of Contents for 2002 FZS600











































































Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands

Yamaha 2002 FZS600, Supplementary Service Manual

Search results

Summary of Contents for 2002 FZS600

Reviews:

Related manuals for 2002 FZS600

Brands by name

Popular brands