background image

 

Table of contents

 

Checking water in engine oil tank ... 63
Checking wiring and connectors ..... 63
Checking propeller .......................... 63
Removing propeller ......................... 64
Installing propeller ........................... 64
Changing gear oil ............................ 65
Inspecting and replacing 

anode(s)........................................ 66

Checking battery (for electric start 

models) ......................................... 67

Connecting the battery .................... 67
Disconnecting the battery ............... 68

 

Trouble Recovery ............................ 69

 

Troubleshooting ............................  69
Temporary action in emergency..... 72

 

Impact damage ............................... 72
Replacing fuse ................................ 72
Power trim and tilt will not 

operate.......................................... 73

Starter will not operate .................... 73
Emergency starting engine ............. 74

 

Engine fails to operate ..................  75

 

Low oil level alert activates ............. 75

 

Top cowling does not unlock .........  76
Treatment of submerged motor...... 76

 

Consumer information.................... 77

 

Important warranty information 

for U.S.A. and Canada ................  77

YAMAHA MOTOR 

CORPORATION, U.S.A.
 OUTBOARD MOTOR TWO 
YEAR LIMITED WARRANTY ...... 79

IMPORTANT WARRANTY 

INFORMATION IF YOU USE 
YOUR YAMAHA OUTSIDE 
THE USA OR CANADA ..............  82

Summary of Contents for 115



























































































Reviews: