Yamaha 115 Owner'S Manual Download Page 33

Page: 33 / 90

Instruments and indicators

alert indicator will start to blink. For further in-
formation, see page 31.

NOTICE

ECM00030

Do not operate the engine without oil. Se-

rious engine damage will occur.

EMU26583

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
31.

NOTICE

ECM00052

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-

gine damage will occur.

EMU26602

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36061

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

1. Oil level indicator

ZMU01867

ZMU01868

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Alert indicator(s)

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

Summary of Contents for 115



























































































Search results

Summary of Contents for 115

Reviews:

Related manuals for 115

Brands by name

Popular brands

Yamaha 115, Owner'S Manual

Search results

Summary of Contents for 115

Reviews:

Related manuals for 115

Brands by name

Popular brands