Yamaha 115 Owner'S Manual Download Page 52

Page: 52 / 90

Operation

●

Confirm that removing the clip from the en-
gine shut-off switch stops the engine.

●

Confirm that the engine cannot be started
with the clip removed from the engine
shut-off switch.

EMU31730

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

NOTICE

ECM01610

Warm up the engine before shifting into
gear. Until the engine is warm, the idle
speed may be higher than normal. High
idle speed can prevent you from shifting
back to neutral. If this occurs, stop the
engine, shift to neutral, then restart the

engine and allow it to warm up.

To shift out of neutral
1.

Pull the neutral interlock trigger up (if
equipped).

Move the remote control lever firmly and
crisply forward (for forward gear) or
backward (for reverse gear) about 35° (a
detent can felt).

To shift from in gear (forward/reverse) to
neutral
1.

Close the throttle so that the engine
slows to idle speed.

After the engine is at idle speed in gear
move the remote control lever firmly and
crisply into the neutral position.

1. Neutral interlock trigger

Summary of Contents for 115



























































































Search results

Summary of Contents for 115

Reviews:

Related manuals for 115

Brands by name

Popular brands

Yamaha 115, Owner'S Manual

Search results

Summary of Contents for 115

Reviews:

Related manuals for 115

Brands by name

Popular brands