Yamaha 115 Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 90

background image

13

Specifications and requirements

EMU31480

Specifications

TIP:

“(AL)” stated in the specification data below
represents the numerical value for the alumi-
num propeller installed.
Likewise, “(SUS)” represents the value for
stainless steel propeller installed and “(PL)”
for plastic propeller installed.

EMU2821C

Dimension:

Overall length:

808 mm (31.8 in)

Overall width:

582 mm (22.9 in)

Overall height L:

1472 mm (58.0 in)

Transom height L:

516 mm (20.3 in)

Weight (without propeller) L:

163.0 kg (359 lb)

Performance:

Full throttle operating range:

4500–5500 r/min

Maximum output:

84.6 kW@5000 r/min
(115 HP@5000 r/min)

Idling speed (in neutral):

750

±

50 r/min

Engine:

Type:

2-stroke V

Displacement:

1730.0 cm

3

Bore

×

stroke:

90.0

×

68.0 mm (3.54

×

2.68 in)

Ignition system:

CDI

Spark plug with resistor (NGK):

BR8HS-10

Spark plug gap:

0.9–1.0 mm (0.035–0.039 in)

Control system:

Remote control

Starting system:

Electric

Starting carburetion system:

Choke valve

Min. cold cranking amps (CCA/SAE):

380.0 A

Min. marine cranking amps (MCA/ABYC):

502.0 A

Min. reserve capacity (RC/SAE):

124 minutes

Maximum generator output:

20.0 A

Drive unit:

Gear positions:

Forward-neutral-reverse

Gear ratio:

2.00 (26/13)

Trim and tilt system:

Power trim and tilt

Propeller mark:

K

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. pump octane:

86

Recommended engine oil:

YAMALUBE 2-stroke outboard motor
oil

Lubrication:

Oil injection

Engine oil tank capacity:

0.9 L (0.95 US qt, 0.79 Imp.qt)

Remote oil tank capacity:

10.5 L (11.10 US qt, 9.24 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

«
...
17
18
19
20
21
...
»

Summary of Contents for 115



























































































Reviews:

No comments

Related manuals for 115

945GC MICRO 775

Brand: Biostar Pages: 49

Brand: ECS Pages: 93

Brand: Texas Instruments Pages: 13

Brand: Ideal-Standard Pages: 20

KEMX-1600 Series

Brand: Quanmax Pages: 74

Brand: ECS Pages: 70

Brand: C&T Solution Pages: 65

Z370 AORUS Gaming 7

Brand: Gigabyte Pages: 48

Brand: MSI Pages: 104

Brand: ASROCK Rack Pages: 83

Brand: Micrel Pages: 10

Brand: Micronics Pages: 63

GENE-9455 Rev.B

Brand: Aaeon Pages: 64

Brand: ASROCK Pages: 4

Brand: Texas Instruments Pages: 33

Brand: AOpen Pages: 8

Brand: ComNav Technology Pages: 28

Brand: Gigabyte Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands