Yamaha 115 Owner'S Manual Download Page 57 | Manualshive

Page: 57 / 90

background image

Operation

51

and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Be sure to retract

the trim rods completely during
mooring. This protects the rods from
marine growth and corrosion which
could damage the power trim and tilt
mechanism.

[ECM00251]

EMU33120

Procedure for tilting down (power
trim and tilt models)

1.

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2.

Release the tilt support lever.

3.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

EMU28061

Shallow water

EMU32851

Power trim and tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU32922

Procedure for power trim and tilt models

1.

Place the remote control lever in neutral.

ZMU03452

ZMU03453

DN

ZMU01936

UP

DN

DN

ZMU04147

«
...
55
56
57
58
59
...
»

Summary of Contents for 115



























































































Reviews:

No comments

Related manuals for 115

Kontron mITX-CFL-S

Brand: S&T Pages: 8

35891900 Series

Brand: PC Partner Pages: 16

Brand: Gigabyte Pages: 17

Brand: ASROCK Pages: 226

Brand: Raider Outboards Pages: 73

Brand: Advantech Pages: 82

Brand: JETWAY Pages: 56

Brand: Micrel Pages: 10

Brand: Acorp Pages: 46

Brand: EVGA Pages: 163

Brand: MATSONIC Pages: 76

Brand: u-blox Pages: 37

Brand: Asus Pages: 2

Brand: ASROCK Pages: 25

Brand: Consumer Microcircuits Pages: 58

Brand: Telit Wireless Solutions Pages: 49

Brand: Asus Pages: 57

Brand: Asus Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands