background image

 

5.

 

Do not use fluxes which contain chloride or acid. Use only rosin or resin activated 

fluxes. 

6.

 

If an oxide film forms, it can be removed by careful buffing with 600-800 grit 

emery cloth, isopropyl alcohol or equivalent and then the tinned areas with 

rosin-core solder after the resin-core has melted. 

 

 

             

 NEW TIPS 

Applying the following steps give the tip optimum life. 

1.

 

Set both temperature to min. then turn the main power switch to the “ON” 

position. 

2.

 

Set soldering tip temperature to 250

 (500

  approx.) and desoldering tip 

temperature to min. Coat the tinned surfaces with rosin-core solder after reaching 

250

3.

 

Set to the desired temperature about 3 minutes after being warmed that the station 

will be ready for sue once it reaches preset temperature. 

 

IMPORTANT: Remove and clean the tip daily. If a new tip is installed, remove any 

loose build up ion the tip and barrel assembly, otherwise the tip may fuse to the 

heating element or retaining barrel. 

                                         

                     

METHOD TO CHECK FOR LOSS OF SUCTION 

The following procedures should be used on LF-8000 to check whether loss of 

suction is due to the tip, solder collector, tube or in-line filter. 

CAUTION

: THE DESOLDER SWITCH MUST BE “OFF” AND ALLOW THE 

IRON TO COLL BEFORE ATTEMPTING THE FOLLOWING PROCEDURES: 

1.

 

Disconnect vacuum tube form the fitting on the front panel, place finger over the 

hole of the fitting, depress vacuum switch and you should have a strong vacuum. 

If not, send back to your nearest service center for pump repair. 

2.

 

Disconnect the inline filter from the iron assembly, depress vacuum switch, 

replace filling of the in-line filter if there is little vacuum pressure or the filters are 

discolored. 

3.

 

Remove solder collector from desolder iron assembly, place finger over the hole 

of the collector, depress vacuum switch. There is little suction clean or replace the 

collector tube. 

4.

 

Depress vacuum witch, clean the tip tube with spring wire provided if there is no 

suction per the “Procedure for Cleaning Clogged Tip” section below. 

                                   

Summary of Contents for LF-8000

















Reviews: