manualshive.com logo in svg

Xvent MiracleAir 300-A1, Instructions For Use And Installation, Page: 23 / 26

Share
Download
Xvent MiracleAir 300-A1 Instructions For Use And Installation Download Page 23

 

23 

 

Version 1 – GBR (05/05/2020) 

D-502-0173 

k)

 

Tighten the pressure caps between the fan and filter box using adequate force. Each new filter box is 
equipped with a new seal to keep the entire assembly tight. If the pressure cap cannot be tightened 
or excessive force is necessary, loosen the cap clip on the thread by 1 turn and repeat the tightening 
process. If excessive force is used to tighten the cap, it or the unit body may get damaged. 

 

 

 

 

 

 

 

 

 

 

 

l)

 

Place the extraction box on the filter box and tighten the pressure caps between it and the filter box. 
Take care to avoid damage the the seal on the filter box and follow the proper positioning on the 
filter box. Each new filter box is equipped with a new seal to keep the entire assembly tight. If the 
pressure cap cannot be tightened or excessive force is necessary, repeat the procedure and adjust 
the pressure as in the previous point k) 
 

m)

 

Attach the extraction box to the suction arm (only for the version of the unit with suction arm) 

 

 

 

 

 

 

 

 

n)

 

Connect the connectors for switch connection, earth connectors and for connectors for the hoset 
Always make sure that the connectors are fitted correctly. 

 

 

 

 

 

  

 

 

ADJUSTING THE 

PRESSURE BY 

TURNING THE CAP 

ALONG THE 

THREAD 

Fig. 25 

Fig. 26 

Fig. 27 

Summary of Contents for MiracleAir 300-A1



























Reviews:

No comments