background image

 

XTEMP ENVIRONMENTS (SHANGHAI) CO., LTD. 

http://www.xtemp-usa.com/

 

 

20

 / 

55 

 

DSEO0711-2-V211119/UXP8401-PG.CC.GE.AR-CD7003/5~+45

 

Chapter 3 Controller Descriptions and Operation 

Based on equipment functions, the message displayed in the HOME screen may 

be different and mainly includes as follows: 

CT, Cabinet Temperature, standard function module, including actual temperature and working 

temperature. Before temperature control starts up, the working temperature is displayed 0.00, 
while after start-up, working temperature correspondences to the actual setting. For 
[CONSTANT] operation, the working temperature is a fixed value, while for [PROGRAM] 
operation, the working temperature will change if the successive two values are set to ramp. 

RH, standard function module, including actual humidity and working humidity. Before humidity 

control starts up, the working humidity is displayed 0.00, while after start-up, working humidity 
correspondences to the actual setting. For [CONSTANT] operation, the working humidity is a 
fixed value, while for [PROGRAM] operation, the working humidity will change if the 
successive two values are set to ramp. 

Humidity control is possible when temperature comes within ±5 °C of the setting. Otherwise the 

humidifier will not work, and the OUTPUT for HUMD will be 0 as illustrated in screen of Details 

for Immediate Constant (Fig 14). 

VL, Visual Light, standard function module, including visual light setting and actual dimming 

output. Light intensity can be set from 0~100%, where 0% means no light, 1~100% means 
dimming between 1~100%. Once light radiation is enabled, or the light intensity is changed 
from one to another, a smooth and comfortable light change is achieved according to a set 
and editable dimming rate. Once outside door open and the operator exposed to strong 
optical light, if the active light intensity is higher than a safety value, the light intensity will be 
dimmed automatically to the safe value. The set value will be resumed once the door closed. 

The Light intensity may be measured by optional light sensors, including quantum sensor for PPF, 

photometric sensor for lux illuminance, and ultraviolet sensor for UVA measurements. The 
display can be instant radiation or accumulative radiation, including 

μ

mol/m

2

.s, klux, W/m

2

mol/m

2

.d (DLI), klux.h and W/m

2

.h for different purpose. The accumulative radiation 

measurements have the advantage of more accurate result to compensate instability of the 
light intensity as affected by voltage fluctuation, temperature and service life of the light. With 
the setting of an accumulative radiation, visual and audible alarm can be used for precise 
radiation control, for example for compliance with ICH Q1B.  

The trend chart is used for record and presentation of temperature and relative humidity changes 

with the time, including actual temperature (Pv), set temperature (Sv), actual humidity (Pv) 
and set humidity (Sv). The left Y axis is temperature (

°

C), the right Y axis is relative humidity 

(%RH), while the X axis is time. The chart start from left and develop to the right, and will pan 
automatically to the left once the chart tends to be full. The scroll bar at the bottom of the 
chart makes review of the temperature and humidity trend vivid and convenient. By touching 

Summary of Contents for UXB8401-PG280


























































Reviews: