Xsensor ForeSite Intelligent Surface System, User Manual

Share

Page: 21 / 47

background image

ForeSite Intelligent Surface System User Guide

Installation

XSENSOR Technology Corporation

21 of 46

Connecting the Power Supply

Insert the power supply connector into the charging port on the side of the Display Terminal.

If your system includes the power supply brace, align the power supply connector between the teeth on the
brace. Push the connector into the brace until it is fully inserted in the charging port.

«
...
19
20
21
22
23
...
»

Summary of Contents for ForeSite Intelligent Surface System
















































Reviews:

No comments

Related manuals for ForeSite Intelligent Surface System

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: Landoll Pages: 34

Brand: AccuMed Pages: 14

Brand: TAS Pages: 25

Brand: Badger Meter Pages: 16

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Haki Pages: 24

Brand: Dakota Digital Pages: 5

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: IBEX Pages: 4

Brand: Quivogne Pages: 13

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands