Xsensor ForeSite Intelligent Surface System, User Manual

Share

Page: 15 / 47

background image

ForeSite Intelligent Surface System User Guide

Installation

XSENSOR Technology Corporation

15 of 46

1.

2.

Installing the ForeSite IS Overlay

The Strapped ForeSite Intelligent Surface Overlay is a fitted mattress cover designed to fit over existing
hospital mattresses that strap to their bed frames.

Unroll the overlay and place it so the zippered pocket is on the top left of the mattress and the

Foot End

label is face up.

Drape the top half of the overlay over the top half of the mattress. Ensure that the corners align.

«
...
13
14
15
16
17
...
»

Summary of Contents for ForeSite Intelligent Surface System
















































Reviews:

No comments

Related manuals for ForeSite Intelligent Surface System

Brand: Laica Pages: 4

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: Landoll Pages: 34

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: MacDon Pages: 46

Brand: MacDon Pages: 82

Brand: Mac Medical Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands