Xsensor ForeSite Intelligent Surface System, User Manual

Share

Page: 18 / 47

background image

ForeSite Intelligent Surface System User Guide

Installation

XSENSOR Technology Corporation

18 of 46

6.

7.

8.

Lift up the long edge of the overlay about 2.5 feet from the corner. A buckle will be located on the
underside.

Feed the strap through the backside of the top buckle slot.

Feed the strap through the front of the bottom buckle slot and tighten till snug. Overtightening is not
required and not recommended. Let the edge of the overlay return to its natural position.

«
...
16
17
18
19
20
...
»

Summary of Contents for ForeSite Intelligent Surface System
















































Reviews:

No comments

Related manuals for ForeSite Intelligent Surface System

Brand: Bartscher Pages: 22

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Ettan IPGphor 3

Brand: GE Pages: 64

Brand: GE Pages: 56

Brand: GE Pages: 132

Brand: GE Pages: 16

Brand: GE Pages: 474

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: SAMCHULLY Pages: 48

Brand: Tate Pages: 7

Brand: Tate Pages: 5

BioHarmonex BH4

Brand: Calivita Pages: 38

Brand: CAIRE Pages: 91

Brand: Eaton Pages: 21

Brand: NANO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands