manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, User Manual

Share
Download
Xilinx Virtex-4 RocketIO User Manual Download Page 83

Embedded Tri-Mode Ethernet MAC User Guide

www.xilinx.com

83

UG074 (v2.2) February 22, 2010

Host Interface

R

Figure 3-43

 shows the timing diagram for reading the multicast address from one of the 

four multicast address registers.

For reading a multicast address register in HOSTWRDATA[31:0], the RNW field is set to 

1

, 

and the multicast address field should be set with the register number to be read. The 
multicast address register read data is returned in HOSTRDDATA[31:0]. The LSW is the 
multicast address [31:0]. The MSW contains 

0x0000

 and the multicast address [47:32]. For 

examples of accessing a multicast address register, see 

“Interfacing to the Processor DCR” 

in Chapter 6

.

HOSTMIIMSEL acts as a read enable. It must be held Low for an even number of clock 
cycles during a read operation.

Using the DCR Bus as the Host Bus

When the DCR bus is used to access the internal registers of the Ethernet MAC, the DCR 
bus bridge in the host interface translates commands carried over the DCR bus into 
Ethernet MAC host bus signals. These signals are then input into one of the Ethernet 
MACs.

The DCR bus bridge contains four device control registers. The first two are used as data 
registers, each is 32 bits wide (dataRegMSW and dataRegLSW). The third is used as a 
control register (cntlReg).

The fourth device control register is used as a ready status register (RDYstatus). The 
PowerPC 405 processor polls this register to determine access completion status. The bits 
in this register are asserted when there is no access in progress. When an access is in 
progress, a bit corresponding to the type of access is automatically deasserted. The bit is 
automatically reasserted when the access is complete. Alternatively, the host interface can 
also provide an interrupt request to inform the host of access completion. The user can 
select either the polling or the interrupt method to inform the host of access status.

Figure 3-43:

Address Filter Multicast Address Register Read

0x38C

M

S

W

HO

S

TRDDATA[31:0]

HO

S

TWRDATA[31:0]

HO

S

TADDR[9:0]

HO

S

TOPCODE[1]

HO

S

TMIIM

S

EL

HO

S

TCLK

L

S

W

UG074_3_45_080805

www.BDTIC.com/XILINX

Summary of Contents for Virtex-4 RocketIO

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands