manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, User Manual

Share
Download
Xilinx Virtex-4 RocketIO User Manual Download Page 163

Embedded Tri-Mode Ethernet MAC User Guide

www.xilinx.com

163

UG074 (v2.2) February 22, 2010

Interfacing to an FPGA Fabric-Based Statistics Block

R

When the Ethernet MAC Is Implemented with the DCR Bus

When the Ethernet MAC is implemented with the DCR bus connected directly to the 
PPC405, the host bus signals of the Ethernet MAC can access the statistics counters.

The host bus I/O signals of the Ethernet MAC are enabled for statistics counter access 
when a DCR read operation is made for address codes 

0x000

 to 

0x02F

 and 

0x040

 to 

0x04F

 inclusive (

Table 3-30, page 91

 describes the DCR address code space). This use of 

the host bus I/O signals provides a means of accessing the FPGA fabric from the processor 
with space for 64 addresses.

When the DCR bus is instructed to access registers in this address code region, the DCR 
bridge translates the DCR commands into generic host read signals on the host bus I/O 
signals. The DCR transaction is encoded on the host bus signals HOSTRDDATA[31:0] and 
HOSTMIIMRDY as described in 

Table 6-2

 and 

Figure 6-2

. These signals can access 

statistics counters in the same way as if a standalone host bus is used. The statistics values 
read from statistics counters are captured from the host bus signals HOSTWRDATA[31:0] 
as shown in 

Figure 6-2

. The data read from the host bus can then be accessed by reading 

the DCR data registers.

Table 6-2:

DCR to Host Mapping

EMAC Host Bus Port

Port Direction on 

EMAC

DCR Register

Equivalent Standalone Host 

Bus Signal

HOSTRDDATA

[15]

Out

HOSTREQ

[14:13]

Out

HOSTOPCODE[1:0]

[10]

Out

cntlReg[21], 

EMAC1Sel

HOSTEMAC1SEL

[9:0]

Out

cntlReg[22:31], 

Address Code

HOSTADDR[9:0]

HOSTMIIMRDY

Out

HOSTMIIMSEL

HOSTWRDATA[31:0]

In

dataRegLSW / 

dataRegMSW

HOSRTRDDATA[31:0]

HOSTMIIMSEL

In

HOSTMIIMRDY

www.BDTIC.com/XILINX

Summary of Contents for Virtex-4 RocketIO

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands