manualshive.com logo in svg

Xilinx Virtex-4 RocketIO, User Manual

Share
Download
Xilinx Virtex-4 RocketIO User Manual Download Page 101

Embedded Tri-Mode Ethernet MAC User Guide

www.xilinx.com

101

UG074 (v2.2) February 22, 2010

Media Independent Interface (MII)

R

MII Clock Management

Figure 4-2

 shows the clock management used with the MII interface. Both the 

MII_TX_CLK_# and MII_RX_CLK_#, generated from the PHY, have a frequency of either 
2.5 MHz or 25 MHz, depending on the operating speed of the Ethernet MACs. The 
MII_TX_CLK drives the MII_TXD registers, the CLIENTEMAC#TXGMIIMIICLKIN and 
the PHYEMAC#MIITXCLK through a BUFG. It has a frequency of 12.5 MHz or 1.25 MHz 
depending on the operating speed of the Ethernet MAC. The RX clocking is similar.

The CLIENTEMAC#DCMLOCKED port must be tied High.

 

MII Clock Management with Clock Enable

It is possible to only use two BUFGs. To accomplish this BUFG reduction, the client and 
MII logic must be constrained to run at 125 MHz. Also clock enable signals must be added 
to the client logic. 

Figure 4-3

 shows the MII clock management with a clock enable scheme.

Figure 4-2:

MII Clock Management

CLIENTEMAC#TXGMIIMIICLKIN 

PHYEMAC#GTXCLK 

CLIENTEMAC#TXCLIENTCLKIN 

EMAC#CLIENTTXCLIENTCLKOUT 

CLIENTEMAC#RXCLIENTCLKIN 

EMAC#CLIENTRXCLIENTCLKOUT 

CLIENTEMAC#DCMLOCKED 

PHYEMAC#RXCLK 

EMAC#PHYTXD[3:0]

PHYEMAC#RXD[3:0]

EMAC# 

BUFG 

TX CLIENT 

LOGIC 

BUFG 

RX CLIENT 

LOGIC 

IBUFG

MII_RX_CLK_#

D

Q

MII_RXD_#[3:0]

IBUF 

OBUF 

MII_TXD_#[3:0]

Q 

D 

BUFG

MII_TX_CLK_#

PHYEMAC#MIITXCLK 

GND 

UG074_3_51_032207

BUFG

(1)

Note 1: A region

a

l 

bu

ffer (BUFR) c

a

n repl

a

ce thi

s

 BUFG. 

Refer to the Virtex-4 U

s

er G

u

ide for BUFR 

usa

ge g

u

ideline

s

.

www.BDTIC.com/XILINX

Summary of Contents for Virtex-4 RocketIO

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands