Xerox WorkCentre 5019, Service Documentation

Page: 26 / 457

08/2012
2-15 WorkCentre 5021/5019
005-147, 005-198/199
Status Indicator RAPs Initial Issue
005-147 DADF Pre Regi Sensor Off Jam on Inverting
BSD-ON: CH5.4 , CH5.5
After the DADF Feed Motor started the reverse rotation at Invert operation, the DADF Pre Regi
Sensor did not turn OFF within the specified time.
Cause/Action
Check the following:
• Transportation failure due to foreign substance on the document path.
• The surface of the Exit Roll, Takeaway Roll, Regi Roll, and Out Roll for foreign sub-
stances.
• The surface of the Exit Roll, Takeaway Roll, Regi Roll, and Out Roll for wear.
• The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. ( PL 56.14 )
• The DADF Feed Motor (Output Check [005-048/008] (CCW/CW)) for operation failure.
(
PL 56.6 )
• The Exit Pinch Roll for operation failure (including for the operation failure of the Exit Nip
Release Solenoid (Output Check [005-072])). (
PL 56.7 )
• The Drive Gear for wear and damage.
If no problem is found, replace the DADF PWB. ( PL 56.2 )
005-196 Size Mismatch Jam on No Mix-Size
BSD-ON: CH5.4 , CH5.2
The 2nd sheet or later of the document was detected to be of a different size conpared to the
1st sheet (the length of the document's 2nd sheet or later in SS direction is longer).
Cause/Action
1. Check the size of the document that was fed by the User.
2. If the error is not cleared, check the following:
• The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. ( PL 56.14 )
• The Document Tray Size Sensor 1/2 (Input Check [005-221/222]) for operation fail-
ure.
( PL 56.11 )
3. If no problem is found, replace the DADF PWB. ( PL 56.2 )
005-197 Prohibit Combine Size Jam
BSD-ON: CH5.4
A Mixed Size document was detected.
Cause/Action
Explain to the User that Mixed Size is not supported.
005-198/199 Too Short Size Jam/ Too Long Size Jam
BSD-ON: CH5.4 , CH5.2
[Too Short Size Jam]
It was detected that the document length in Slow Scan direction is shorter than the specifica-
tions (Simpex: 85 mm, Duplex: 110 mm).
[Too Long Size Jam]
It was detected that the document length in Slow Scan direction is at the specifications (Sim-
pex: 1275 mm, Duplex: 480.1 mm) or longer.
Cause/Action
Check the size of the document that was fed by the user. If it is within the permitted length for
DADF transport, check the following:
• The DADF Pre Regi Sensor (Input Check [005-206]) for operation failure. ( PL 56.14 )
• The Document Tray Size Sensor 1/2 (Input Check [005-221/222]) for operation failure.
(
PL 56.11 )
If no problem is found, replace the DADF PWB. ( PL 56.2 )
005-210 DADF Download Fail
BSD-ON: CH3.1
When the IISS starts up (including at Power ON/Sleep recovery), it was detected that the
DADF is in Download Mode.
Cause/Action
Perform the DADF software download.
005-275/280 DADF RAM Fail/ DADF EEPROM Fail
BSD-ON: CH3.1
[DADF RAM Fail]
The DADF PWB RAM failed during the Read/Write operation. (At Power ON)
[DADF EEPROM Fail]