Xerox M20 - WorkCentre B/W Laser Service Manual Download Page 125

Page: 125 / 314

December 2006

4-27

WorkCentre M20, 4118, FaxCentre 2218 Family

REP 5.1

Repairs and Adjustments

Prepare to remove the MEA unit cover open, Figure 7.

NOTE: Removing the 4 screws that secure the guide - M scan assembly will ease the
removal of the MEA unit cover open.

Figure 7 Preparation

Remove the MEA unit cover open, Figure 8.

Figure 8 MEA unit - cover open removal

10. Remove the MEA unit guide duplex, Figure 9.

Figure 9 MEA unit guide duplex removal

Remove 4 screws.

Open the MEA unit - cover
open

Disconnect CN5 and 1 ground
harness.

Align the flat on the rear pivot with
the slot in the frame. Remove the
MEA unit - cover open from the rear
pivot, then the front pivot.

Remove the MEA unit
guide duplex.

Summary of Contents for M20 - WorkCentre B/W Laser



























































































































































































































































































































Search results

Summary of Contents for M20 - WorkCentre B/W Laser

Reviews:

Related manuals for M20 - WorkCentre B/W Laser

Brands by name

Popular brands

Xerox M20 - WorkCentre B/W Laser, Service Manual

Search results

Summary of Contents for M20 - WorkCentre B/W Laser

Reviews:

Related manuals for M20 - WorkCentre B/W Laser

Brands by name

Popular brands