Xerox DocuPrint 2065 User Manual Download Page 236

Page: 236 / 240

From

B (bottom left)

([Network / Port] continued)

TCP/IP

Get IP Address

IP Address,
Subnet Mask,
Gateway Address

DHCP/Autonet

, DHCP,

BOOTP, RARP, Panel
000.000.000.000

nnn.nnn.nnn.nnn

InternetServices

Port Status

Enable

Disable

Enter when [Get IP Address]
is [Panel]

Displays the printer’s IP address
when [Get IP Address]
is not [Panel]

Ethernet

Auto

, 100M FullDuplex, 100M HalfDuplex,

10M Full Duplex, 10M Half Duplex

IPX/SPXFrameType

Network Settings

Auto

, Ethernet II, Ethernet 802.3,

Ethernet 802.2, Ethernet SNAP

FTP

Port Status

Enable

Disable

StatusMessenger

Port Status

Enable

Disable

Bonjour

Port Status

Enable

Disable

Adobe Protocol

Auto

, Standard, BCP,

TBCP, Binary

IP Filter

No.1/Address

No.1/Mask

No.1/Mode

HTTP - SSL/TLS

Enable / Disable

Disable

Enable

000.000.000.000

Off

Permit, Reject

No.5/Address

No.5/Mask

No.5/Mode

000.000.000.000

Off

Permit, Reject

This item appears only when a certificate is registered in the printer.

These items do not appear on the model available in China.

Summary of Contents for DocuPrint 2065
















































































































































































































































Search results

Summary of Contents for DocuPrint 2065

Reviews:

Related manuals for DocuPrint 2065

Brands by name

Popular brands

Xerox DocuPrint 2065, User Manual

Search results

Summary of Contents for DocuPrint 2065

Reviews:

Related manuals for DocuPrint 2065

Brands by name

Popular brands