manualshive.com logo in svg

Xerox DocuPrint 2065, User Manual, Page: 121 / 240

Share
Download
Xerox DocuPrint 2065 User Manual Download Page 121

5.2 Setting the Common Menus

121

[mm/inch]

[Overwrite HDD]

Note

• [Overwrite HDD] appears only when the internal hard disk (optional) is installed.

[Print Auditron]

System Settings

mm/inch

Setting Item

Description

mm/inch

Sets the unit of measure for length that will be displayed or entered on the con-
trol panel.
• [Millimeters (mm)] (default)

Indicates length in millimeters (mm).

• [Inch (")]

Indicates length in inches (").

System Settings

Overwrite HDD

Setting Item

Description

Overwrite HDD

Sets whether to overwrite the data stored in the internal hard disk (optional) 
when the internal hard disk is installed. If overwriting the data, set the number 
of times to overwrite the data to either once or three times.
• [3 Overwrites] (default)
• [1 Overwrite]
• [Off]

System Settings

Print Auditron

Setting Item

Description

Print Auditron

Sets whether or not to enable the Print Auditron feature.
• [Off] (default)
• [On]

Note

• After changing this setting, reboot the printer.

Refer to

• "7.8 Authentication and Auditron Administration Features" (P. 181)

Summary of Contents for DocuPrint 2065

















































































































































































































































Reviews:

No comments