Xerox DocuColor 5252 Administration Manual Download Page 2

Page: 2 / 108

DocuColor 5252 System Administration Guide

2-2

Tools Mode

Entering Tools Mode

Use the following procedure to enter the Tools Mode:

Press the

Access

button on the Control Panel. The

Access

Password

Screen appears.

Use the keypad to enter the Tools Mode password. The default
password is five 1s (

11111

). For security reasons, only asterisks

are displayed on the screen.

Touch the

Enter

button on the screen. The Pathway Options

screen appears:

Note:

It is recommended that you change the Tools password as

soon as possible after installing the digital press to prevent
unauthorized access to the Tools Mode. The procedure for
changing the password is in the next chapter.

Touch the

Tools Pathway

button on the screen.

Summary of Contents for DocuColor 5252













































































































Search results

Summary of Contents for DocuColor 5252

Reviews:

Related manuals for DocuColor 5252

Brands by name

Popular brands

Xerox DocuColor 5252, Administration Manual

Search results

Summary of Contents for DocuColor 5252

Reviews:

Related manuals for DocuColor 5252

Brands by name

Popular brands