background image

User manual XC-32 XC-320 XC-4200

III.7.2 - Note

III.7.2.1 - About XC-32

Security of this equipment is guaranteed only if you use the furnished power supply or an
equivalent model.
Cables must only be plug at very low security voltages (VLSV).

Warning

This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

III.7.2.2 - General note

The hardware and software described in this document may change without warning.
The information in this document may change without warning. Xcell Technology reserves
itself the right to revise this publication without having to provide notification for such
revisions. Aslong as reasonable precautions have been taken, Xcell Technology assumes
no responsibility for errors that may appear in this document.

Xcell Technology

 is a registered trademark of 

DECISION Europe

.

No part of this publication may be copied or reproduced in any form or by means without
prior written consent of Xcell Technology.
Windows and Microsoft Windows are trademarks of Microsoft Corporation. Ethernet is a
trademark of the Xerox corporation. Netscape is a trademark of Netscape
Communications Corporation.
All other brand and product names and trademarks mentioned herein are trademarks of
their respective owners.

-15-

Summary of Contents for XC-32





























































































Reviews: