background image

Page: 8 

 

SmartPad LCD

¥

© 2006 Xantech Corporation 

 

SmartPad LCD FEATURES 

ƒ

LCD Touch Screen Interface:

 Allows for use of GTL’s (Graphical Touch Link). Colorful graphical 

representation of functional buttons for touch control of IR and RS232 controlled devices 

ƒ

Upper and Lower Viewing Angles:

 Software Programmable for exact viewing placement 

ƒ

Programmable Backlight Control:

 Selectable Time-Out for LCD backlight 

ƒ

Standard Xantech IR Bus Output: 

Allows for easy interface to existing IR networks 

ƒ

Internal IR Code Library:

 Built in IR Code Library. Contains all Major Brand Component IR commands. No 

need to ‘learn’ commands.  

ƒ

IR Learning:

 IR commands can be learned from external hand-held remotes through the 

SmartPad LCD’s

built-in IR learning eye to add to the CSPLCD’s built-in IR code library. 

ƒ

Macros:

 can be built using IR, RS232, repeat or delay commands and associated with a specific button or 

event triggered by a keypad button press, an RC68+ IR code, an MRC88 compatible keypad 
command, control sense status, or by RS232. Up to 40 IR commands can be issued in a single 
Macro.

ƒ

IR Receiver: 

Broad-band IR Receiver for pass through of IR commands from Hand-Held IR Remotes 

ƒ

TalkBack / Status LED: 

LED indicates presence of IR and/or programmable STATUS indication of Zone or 

other user defined power on/off indicator. 

ƒ

RC68+ IR Trigger Sequencer

: Trigger IR and/or RS232 Macros via RC68+ IR command received at the 

built-in IR Receiver 

ƒ

Status Input

: Trigger IR and/or RS232 Macros with a voltage between 5-30VDC 

ƒ

Status Output: 

Send a 12VDC output voltage to trigger the on/off state of another device or indicator 

ƒ

Serial IO: 

RS232 control over an RS422 line for RS232 control of remotely located RS232 controlled 

devices (Require optional RS422232 adapter). 

ƒ

CM8X8/MRC88 Plug-N-Play:

 Direct connect to standard Keypad Input of CM8X8/MRC88CTL for full zone 

control

ƒ

RS232 Com/USB Com Programming Ports:

 Communication Programming Ports located on the front 

panel of the CSPLCD under the bezel, used to program the system using Universal Dragon Drop-
IR™ Software 

ƒ

Emitter Output:

 Local Emitter port on rear of CSPLCD 

ƒ

Full Motion Video Input (CSPLCD64V only):

 NTSC/PAL composite video input for full motion video 

display on PIP display or full screen 

ƒ

Firmware Upgradeable for ‘Future Proof’ Technology: 

Upgradeable via RS232 Com Port or USB 

programming. Firmware upgrades available for easy download by following LINK’s within Universal 
Dragon Drop-IR Software 

Summary of Contents for CSPLCD39G

















































































Reviews: