4.7.
Remove the protective film from the PINLOCK
®
inner visor and check that the
entire silicone-sealed profile of the inner visor adheres to the visor.
4.8.
Fit the visor on the helmet (see instructions above).
Checking and Adjusting the PINLOCK
®
Inner Visor Stretch
Check the correct PINLOCK
®
inner visor assembly by opening and closing the visor
and making sure that they do not move.
If the PINLOCK
®
inner visor is not tightly fixed to the visor, move both external adju-
stment levers upwards to increase the stretch (Fig. 5). This operation must be carried
out gradually. The maximum stretch is achieved when the pin adjustment external
levers are turned outwards
WARNING
-
The presence of dust between the two visors may produce scratches on both
surfaces.
-
Scratched PINLOCK
®
visors and inner visors may cause reduced visibility and
must therefore be replaced.
-
Regularly check the correct stretch of the PINLOCK
®
inner visor to prevent the
it from moving and scratching both surfaces.
-
If the helmet visor fogs up and/or condensation forms between the visors,
check that the PINLOCK
®
inner visor is both correctly assembled and stret-
ched.
-
An excessive and early stretch of the PINLOCK
®
inner visor may result in
excessive adherence against the visor surface and/or permanent deformations
with subsequent inability to correctly perform any following adjustments.
-
Intense sweating /breathing, the use under particular weather conditions (low
temperatures, and/or high humidity and/or sudden changes in temperature
and/or heavy rain) and/or intense and prolonged use may affect the performan-
ce of the PINLOCK
®
inner visor and cause fogging or formation of condensa-
tion. In such cases, after using the helmet and to restore the system efficien-
cy, remove the PINLOCK
®
inner visor from the helmet visor and let it dry with
dry and warm air. The same procedure must be applied to the helmet, in order
to dry out humidity in case it has formed up as a consequence of the condi-
tions described above.
5.
Inner Visor PINLOCK
®
Disassembly
5.1.
Remove the visor equipped with the Pinlock
®
inner visor (see instructions
above).
5.2.
Widen the visor and release the Pinlock
®
inner visor from the pins (Fig. 7).
5.3.
Release the visor.
Maintenance and Cleaning
-
Remove the PINLOCK
®
inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
-
Dry the inner visor with dry and warm air without wiping it.
-
To keep the features of the inner visor in good conditions over time, let the hel-
met dry in a ventilated and dry place with the visor open after use. Keep it
16
Summary of Contents for X-661
