X-GLOO 4x4 User Manual Download Page 3

Page: 3 / 25

Tel. +49 (0) 86 41- 69 48 - 60 | www.x-gloo.com | [email protected]

TABLE OF CONTENTS

TECHNICAL DATA

STANDARD DELIVERY

SPECIAL INSTRUCTIONS

SETUP

1. Lay out the Matrix

..........................

2. Test the Valves

.................................

3. Inflate

............................................

8-9

Inflation with the Hand Pump

..........

Inflation with the Electric Pump

Bravo OV10/Bravo 2000

....................

Inflation with the Bravo

Turbo Max 12 V for car battery

.........

Setup using the Protection Foil

........

STABILISATION

Stabilisation with Water Ballasts

Stabilisation with Sand Ballasts

....

Stabilisation with

Water Ballast Barrels

........................

Stabilisation with the

Anchoring Set

....................................

ELEMENTS

Side Walls

...........................................

Tunnel Part

.........................................

Canopy and Canopy Banner

.............

LED Lighting Kit

................................

BLOCK-BUILDING SYSTEM /

X-GLOO MATRIX

TAKEDOWN

CLEANING

REPAIR

Bladder Repair

...................................

Replacement of the

Protection Strip

.................................

Bladder Replacement

.......................

X-RELAX

Summary of Contents for 4x4


























Search results

Summary of Contents for 4x4

Reviews:

Related manuals for 4x4

Brands by name

Popular brands

X-GLOO 4x4, User Manual

Search results

Summary of Contents for 4x4

Reviews:

Related manuals for 4x4

Brands by name

Popular brands