background image

14 

PROBLEM:

  

Push product button and no syrup is dispensed.

  

 

POSSIBLE SOLUTION:  *Check to make sure there is product in Syrup tank or BIB containers. *

Check prod-

uct connection at BIB container’s outlet fitting and the pump. *Check CO2 supply to syrup tank or BIB pump.

 

* Is product or pump inlet line kinked or crimped? *Is shut off screw in closed position? 

Open shut off screw. *

 

Is brix screwed in too far? 

Open brix screw.  

 

PROBLEM:  Push soda button and no soda is dispensed. 

POSSIBLE SOLUTION: * Is carbonator plugged in? 

Check power supply.

 * Is water supply to carbonator on? 

Check water supply. *

 Check CO2 supply to carbonator. * Is line kinked or crimped? *Is shut off screw in 

closed position?  

Open shut off screw (page 3). *

 Is brix screw screwed in too far? 

Open brix screw (page 3). 

Is proper butterfly configuration being used? 

Check butterfly maps on pages 8 and 9.   

 

PROBLEM:  Push water button and no water is dispensed. 

POSSIBLE SOLUTION: *

 Check water supply. *

 Is line kinked or crimped. *Is shut off screw in closed posi-

tion? 

Open shut off screw. *

 Is brix screw screwed in too far? 

Open brix screw. *

 Is proper butterfly configura-

tion being used?  

Check Butterfly map. 

 

PROBLEM:  Push product  button, dispenses wrong product.  

POSSIBLE SOLUTION:  *Is correct BIB container connected to proper BIB pump? 

Check BIB product con-

tainer and pump. *

 Is correct product tubing connected to proper position on manifold? 

Check connection at  

brix manifold. 

 

PROBLEM: Product(s) taste “weak” or watered down.  

POSSIBLE SOLUTION:  Was dispenser brixed at proper operating temperature? Make sure cold plate is 
iced down correctly. * Is CO2 supply to containers or pumps set properly? 

Check CO2 supply and regulators, 

adjust to correct settings. Check CO2 supply to carbonator, set high pressure regulator between (95-105 
PSI). Check brix screw on soda and/or water positions. Check brix screws on product. Check to be certain 
shut off screw slots are in proper position. (Flow runs in same direction as slot.) Rebrix the dispenser.

 

 

PROBLEM:  Product(s) taste “strong” or syrupy. 

POSSIBLE SOLUTION: Was dispenser brixed at proper operating temperature? Make sure cold plate is iced 
down correctly. * Is CO2 supply to containers or pumps set properly? Check CO2 supply and regulators, ad-
just to correct settings. 

Check CO2 supply to carbonator, set high pressure regulator between (95-105 psi). 

Check brix screw on soda and/or water positions. Check brix screws on product. Check to be certain shut off 
screw slots are in proper position. (Flow runs in same direction as slot.) Re-brix dispenser. 

 

PROBLEM: Push button and release, product keeps dispensing. 

POSSIBLE SOLUTION:  * Butterfly plates are too tight. Remove button plate and loosen butterfly retainers, 
these only need to be snug. 

Do not over tighten!

* Debris caught in cork o- ring. Hold hand over nozzle, de-

press all buttons at once, back flushing dispenser.  This may dislodge particle enough to pass through dis-
penser. 

Change cork o-ring

 

PROBLEM:  When button is depressed, product oozes from under button plate. 

POSSIBLE SOLUTION:  * Stem o-ring defective. 

Replace stem o-ring (p/n PH10-20).

 

 

PROBLEM:  Product leaks or drips out  of  nozzle. 

POSSIBLE SOLUTION:  * Cork o-ring (older models) or molded valve is defective. 

Replace cork o-ring or 

replace entire valve with new molded valve stem (p/n  PH10-89). 

 

PROBLEM:  Product leaking  around bottom plate. 

POSSIBLE SOLUTION:  * Hat o-ring has failed. 

Replace hat o-ring (p/n PH10-26).  

 




MARK 4 MANUAL 

www.wunderbar.com 

Summary of Contents for Mark 4



























Reviews: