background image

OWNER’S /

OPERATOR’S

MANUAL

MODEL NO’s

SDM40-48
SDM40-60
SDM40-72

CAUTION

For Safe Operation

Read Rules And

Instructions Carefully

SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.

S A F E T Y   P R E C A U T I O N S

MOST ACCIDENTS OCCUR BECAUSE OF NEGLECT OR CARELESSNESS.

AVOID NEEDLESS ACCIDENTS BY FOLLOWING ALL OF THE SAFETY PRECAUTIONS LISTED BELOW.

• Machinery should be operated only by those who 

are responsible and are authorized to do so.

• Stop the engine, lower all equipment, lock the 

brakes, and remove the ignition key before dis-
mounting from the tractor.

• Never stand between tractor and implement while 

tractor is being backed to hitch.

• Loose fitting clothing should not be worn, to avoid 

catching on various parts.

• Detach implement in area where children normally 

do not play.

• When performing adjustments or maintenance on

an implement, first lower it to the ground or block it
securely at a workable height.

• Only a qualified operator should be permitted on

tractor when in operation; no riders allowed.

• Make certain everyone is in the clear before starting 

tractor or raising or lowering equipment.

• Operate the tractor and implement only while

seated in the driver’s seat.

• Reduce speed when transporting mounted

implements to avoid bouncing and momentary loss
of steering control.

• A heavy load can cause instability of the tractor.

Use extreme care during road travel. Slow down on 
turns and watch out for bumps. Tractor may need
front counter-weights to counter-balance the weight
of the implement.

• Reduce speed on hillsides or curves so there is no 

danger of tipping.

• Avoid driving too close to the edge of ditches or 

creeks.

• Do not transport implement on public roads without 

reflectors and slow moving vehicle emblem in
daylight and with approved warning lights at night
and other periods of poor visibility.

• Due to the width of some implements, use extra

caution on highways, farm roads, and when
approaching gates.

• Always be sure the implement is in the proper

position for transport.

• Keep alert and watch the front as well as the rear 

when working with the implement.

OWNER’S /

OPERATOR’S

MANUAL

MODEL NO’s

SDM40-48
SDM40-60
SDM40-72

WHEN ORDERING

REPAIR PARTS,

ALWAYS GIVE

THE FOLLOWING

INFORMATION:

1.  PART NUMBER
2.  PART DESCRIPTION
3.  MODEL NUMBER
4.  NAME OF ITEM

OCTOBER 2001

WS-RM002-OG

W O R K S AVER, INC.

P.O. BOX 100    LITCHFIELD, IL 62056-0100    (217) 324-5973

WEB: http:// www.worksaver.com    E-MAIL: [email protected]

Equip tractors with roll-over protection
(ROPS) and keep all machinery guards in
place.

Keep children away from danger all day,
every day . . .

Please work, drive, play and live each day
with care and concern for  your safety and
that of your family and fellow citizens.

MAKE EVERY DAY

A HOLIDAY

FROM ACCIDENTS

STANDARD DUTY 3-PT. MOUNTED

ROTARY CUTTER

Safety Instructions

Operating Instructions

Maintenance

Tractor Preparation

Assembly & Mounting

Repair Parts

C A U T I O N

THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD

BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE

1. Select an area for assembly that is clean and free

of any debris which might cause persons working
on the assembly to trip.

2. Do not lift heavy parts or assemblies. Use crane,

jack, tackle, fork trucks or other mechanical devices.

3. Preview the assembly instructions in your opera-

tor’s manual before proceeding further.

4. If the assembly instructions call for parts or assem-

blies to be blocked up, use only blocking material
that is in good condition and is capable of handling
the weight of the assembly to be blocked. Also
insure that the blocking material is on a clean, dry
surface.

5. Never put hands, or any part of body, under

blocked up assemblies if at all possible.

6. After completing assembly, thoroughly inspect the

machine to be sure that all nuts, bolts, hydraulic fit-
tings or any other fastened assemblies have been
thoroughly tightened.

7. Before operating the machine, thoroughly read the

operation section of your operator’s manual.

8. Before operating, read the maintenance section of

your operator’s manual to be sure that any parts
requiring lubrication, such as gearboxes, are full, to
avoid any possible damage.

9. Before operating equipment – If you have any

questions regarding the proper assembly or
operation, contact your Worksaver dealer or
representative.

Summary of Contents for SDM40-48









































Reviews: