Wood-mizer Sawmill Safety, Operation, Maintenance & Parts Manual Download Page 24 | Manualshive

Page: 24 / 47

background image

Installation & Setup

Board Stop Adjustment

3

3-15

TD02doc072519

Installation & Setup

3.5

Board Stop Adjustment

The Board Stop Assembly can be mounted to either of the Transfer Deck sides. Install the
board stop on the side opposite to the direction from which the lumber is flowing. The
boards will stop as soon as they hit the board stop assembly.

WARNING!

Keep all persons out of the moving equipment

and boards while operating transfer deck. Failure to do so
may result in serious injury or death.

Adjust the accessory roller width to suit your application. To adjust the board stop:

1.

Lift and turn the two pins securing the board stop in its closest-to-table position.

2.

Move the board stop assembly so that it is long enough to make the lumber fit the transfer
deck table. The maximum board dimension to be used with the transfer deck can not
exceed 16 ft. (4.88m).

See Figure 3-14.

3.

Secure the board stop assembly with the two locking pins when the adjustment is com-
plete.

FIG. 3-14 TRANSFER DECK (TD1)

Lift and turn the locking pin (2)
and adjust the board stop;
secure the board stop

with the locking pin when
the adjusment is complete

TD0011

«
...
22
23
24
25
26
...
»

Summary of Contents for Sawmill
















































Reviews:

No comments

Related manuals for Sawmill

Brand: Ecco Pages: 9

Brand: Talet Equipment Pages: 17

Brand: Danelec Pages: 67

Brand: Garelick Pages: 2

Brand: Gardico Pages: 2

Brand: OceanSat Pages: 85

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: YOKOGAWA Pages: 75

Brand: Sota Pages: 7

Brand: Measumax Pages: 2

Brand: Woods Pages: 40

Ology Walkstation 1451458001

Brand: Steelcase Pages: 38

SnapTable PRO Hyper-Lite

Brand: SWENSON SHEAR Pages: 12

Brand: Thoratec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands