manualshive.com logo in svg

Wood-mizer Sawmill, Safety, Operation, Maintenance & Parts Manual

Introducing the Wood-Mizer Sawmill, a cutting-edge product designed to deliver precise and efficient results. Ensure safety, smooth operation, and optimal maintenance with our comprehensive Safety, Operation, Maintenance & Parts Manual, available for free download at manualshive.com. Enhance your woodworking experience with this invaluable manual.

Share
Download
background image

Installation & Setup

Setup

3

3-11

TD02doc072519

Installation & Setup

Adjust the legs so each leg is in contact with the ground. Loosen the locking bolt. Turn the
adjustment  bolt  clockwise  to  raise,  turn  counterclockwise  to  lower  the  transfer  deck
frame. 

See Figure 3-11. 

Secure the leg with the locking bolt. Tighten the jam nuts when the adjustment is com-
plete.

FIG. 3-11 TRANSFER DECK (TD1)

TD0005

Locking Bolt

Adjustment Bolt

Jam Nut

Summary of Contents for Sawmill
















































Reviews:

No comments

Related manuals for Sawmill

Calistair C300 Translation Of The Original Operating Instructions preview
C300
Brand: Calistair Pages: 44
Baker Hughes Druck DPI 880 Instruction Manual preview
Druck DPI 880
Brand: Baker Hughes Pages: 168
Baroness TDA1200 Owner'S Operating Manual preview
TDA1200
Brand: Baroness Pages: 40
Baroness SP05 Owner'S Operating Manual preview
SP05
Brand: Baroness Pages: 40
BARKO LOADERS 295 Service Manual preview
295
Brand: BARKO LOADERS Pages: 85
Echo WT-1610 Instruction Sheet preview
WT-1610
Brand: Echo Pages: 6
Echo Pro Attachment Series Manual preview
Pro Attachment Series
Brand: Echo Pages: 28
Echo BRD-280 Specifications preview
BRD-280
Brand: Echo Pages: 2
Ecco Pro Vantage 12+ Series Mounting Instructions preview
Pro Vantage 12+ Series
Brand: Ecco Pages: 6
Eaton SafeLite Mounting And Operating Instructions preview
SafeLite
Brand: Eaton Pages: 16
Eaton EMS-2 Instruction Leaflet preview
EMS-2
Brand: Eaton Pages: 6
Ecco 21 Series Installation Instructions Manual preview
21 Series
Brand: Ecco Pages: 17
Gaspardo SP SPRINT Manual preview
SP SPRINT
Brand: Gaspardo Pages: 16
Gastrodomus PH100 Installation, Operating And Service Instructions preview
PH100
Brand: Gastrodomus Pages: 4
HANYOUNG NUX HL Series Instruction Manual preview
HL Series
Brand: HANYOUNG NUX Pages: 2
Gastrodomus CL Instructions For Use And Maintenance Manual preview
CL
Brand: Gastrodomus Pages: 39
ParaBody 474 Instruction Sheet preview
474
Brand: ParaBody Pages: 3
Hach SIGMA 900 Instrument Manual preview
SIGMA 900
Brand: Hach Pages: 52

Brands by name

Popular brands

Load more brands