Wood-mizer Sawmill Safety, Operation, Maintenance & Parts Manual Download Page 16 | Manualshive

Page: 16 / 47

background image

Installation & Setup

Installation

3

3-7

TD02doc072519

Installation & Setup

6.

Install each of six table rollers to the transfer deck table. Use four 3/8-16 X 3/4 hex head
bolts and 3/8-16 hex nylon lock nuts at the lower section of the transfer deck table.
Tighten the bolts and nuts. Use two 3/8-16 X 3/4 hex head bolts and 3/8-16 hex nylon lock
nuts. Secure the table roller at the upper section of the transfer deck table.

See Figure 3-7.

NOTE:

Make sure all the bolts and nuts are tightened before operating the transfer deck

table.

7.

Make the appropriate air hoses connections.

See Section 3.2 Air Installation

, for transfer

deck air system diagram.

FIG. 3-7

TD0021

3/8-16 X 3/4 Hex Head Bolt (4)

3/8-16 Hex Nylon
Lock Nut (4)

3/8-16 X 3/4 Hex Head Bolt (2)

3/8-16 Hex Nylon
Lock Nut (2)

Table Roller

«
...
14
15
16
17
18
...
»

Summary of Contents for Sawmill
















































Reviews:

No comments

Related manuals for Sawmill

Brand: Sagola Pages: 8

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Far Tools Pages: 25

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: JB-Lighting Pages: 32

Brand: W&H Pages: 72

Brand: Macht Dental Pages: 8

Brand: T&D Pages: 28

Brand: H&S Pages: 54

Brand: Samson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands