WM Systems M2M Industrial Router User Manual Download Page 77 | Manualshive

Page: 77 / 79

background image

Always use the proper antenna type regarding to the module and mobile network, which is

harmonized to the frequency/band. In other way the router will not abble to access the network.
Note that for Narrow Band (NB-IoT) networks it could be needed to wait 5-15 minutes for the first
successfully network registration.

RS485 connection

You can connect meters and measuring systems to the router with an RS485 cable using the RS485
terminal connector, with the appropriate cable. Data communication can be defined in the

Services

/ Ser2net

menu, by enabling and configuring the

RS485

option, and according the TFTP settings

(of FTP data transmission).

«
...
75
76
77
78
79
»

Summary of Contents for M2M Industrial Router
















































































Reviews:

No comments

Related manuals for M2M Industrial Router

Brand: IBM Pages: 72

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

COMSPHERE 6800 Series

Brand: Paradyne Pages: 155

COMSPHERE 6800 Series

Brand: Paradyne Pages: 44

Brand: DCE Pages: 5

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Brand: Falcon Pages: 24

Brand: Clavister Pages: 89

Brand: TRENDnet Pages: 2

Brand: Aztech Pages: 2

BladeCenter Management Module

Brand: IBM Pages: 184

DSL5068EN(1T1R)

Brand: Aztech Pages: 40

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: Zonet Pages: 53

Brand: WAGO Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands