Wildfire BF960SL User Instructions, Installation Instructions, Service Instructions Download Page 1 | Manualshive

Page: 1 / 40

background image

USER INSTRUCTIONS

INSTALLATION INSTRUCTIONS

SERVICE INSTRUCTIONS

It is a regulaon that these instrucons be handed to the customer aer installaon is complete. It is
also the responsibility of the installaon engineer to ensure that the customer is able to fully operate
the appliance and is aware of any cleaning or maintenance requirements.

BF960SL BALANCED FLUE

ROOM SEALED GAS FIRE

Model numbers: F-111XX2 SLIDE for use on Natural Gas (G20) at a supply pressure of 20 mbar in GB / I.E.

(X denotes trim type)

P-XX1584 ISSUE 4

THESE INSTRUCTIONS ARE TO BE LEFT WITH

THE CUSTOMER AFTER INSTALLATION

Do not use this appliance if the front glass panel is broken, removed or ﬁ8ed incorrectly.

1
2
3
...
»

Summary of Contents for BF960SL









































Reviews:

No comments

Related manuals for BF960SL

Brand: Pacific energy Pages: 20

ARGENTO H Series

Brand: M Design Pages: 18

Brand: Desa Pages: 4

Brand: pleasant hearth Pages: 30

PONDEROSA LS-24P-1

Brand: White Mountain Hearth Pages: 12

Brand: Napoleon Pages: 36

Brand: Napoleon Pages: 124

FPB-25SFBS22MT-N

Brand: Firegear Pages: 22

Brand: kozy heat Pages: 8

Brand: Vanguard Pages: 6

CASUAL FIRESIDE 5110-2872O-E

Brand: OW Lee Pages: 28

Brand: Napoleon Pages: 80

Astound-Built In Series

Brand: Napoleon Pages: 80

Brand: baltur Pages: 114

Brand: HearthStone Pages: 44

True Vision 1000 RD

Brand: M Design Pages: 26

Brand: GTI Pages: 22

Brand: Blaze Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands