background image

3 • System Setup

WHITESTAR SIGNATURE™ System

Rx Only – Z370147 Rev. C 1008

3-2

Safety Precautions

Now that the system is set up and you have verified that all of the functions are 
operating properly, you are almost ready to use your WHITESTAR 
SIGNATURE™ System.

Read the following Safety Precautions and Warnings carefully before you use the 
WHITESTAR SIGNATURE™ System in surgery.

1. The WHITESTAR SIGNATURE™ System is equipped with 3-prong power 

plug which must be plugged into an outlet with a ground receptacle.

If the plug does not fit the outlet, contact an electrician. DO NOT modify or 
remove the ground pin.

2. Do not use extension cords with your system.

3. Do not overload your electrical receptacle (outlet).

4. If the cord or plug is damaged, do not use the instrument. An electric shock or 

fire hazard can result. Call AMO customer service to order a new cord.

5. The instrument has ventilation openings at the rear of the console to allow 

ambient air intake and the release of heat generated during operation. If the 
openings are blocked, heat build-up can cause system failures which can result 
in a fire hazard.

6. Do not try to move the WHITESTAR SIGNATURE™ System cart on deep 

pile carpets or over objects on the floor such as cables and power cords.

7. Take care not to trip over power and footpedal cords.

8. Do not try to lift the WHITESTAR SIGNATURE™ System cart.

9. Do not place the instrument on uneven or sloped surfaces.

10. Do not use disposables, accessories or other surgical instruments that are not 

designed for this system. Use only parts recommended by AMO to achieve 
optimum performance and safety.

11. Do not operate the WHITESTAR SIGNATURE™ System in a condensing 

environment. Take care to protect the instrument from fluid sprays or fluid 
buildup.

12. To protect the patient from contaminated fluids or handpieces, use only: 

• sterile tubing cassettes

• sterile irrigation fluid

• sterile handpieces

13. Use caution when you extend, retract or swivel the Mayo stand articulating 

arm. Stay clear of the hinged hardware.

14. Use caution when you use handpieces with sharp edges or pointed tips.

Summary of Contents for SIGNATURE





































































































Reviews: