manualshive.com logo in svg

Whisper Power 61242040, User Manual

Share
Download
Whisper Power 61242040 User Manual Download Page 28

28       WhisperPower Inverter / Battery Charger

   

E11

Bad Battery

  classification:  E01  (By-Pass  Mode) 

condition has not been solved. AC Charger has 
shutdown. 

- Check corrective action in E01 (By-pass Mode) 

and restart the charging process by removing 
and reconnecting the AC Input Source.

Other conditions leading to Bad Battery 
Classification: Battery Voltage remains below 19V 
after 15 minutes of charge. 

- Check if there is any heavy DC load connected 

to the battery as stated in E01 (By-pass mode). 
Restart the charging process.

- Change to a new battery.

E12

When unit is in By-Pass mode, Internal 

transfer 

switch temperature is high

 and shutdown occurs.

Reduce load and check if any ventilation of the 
unit is blocked.

E13

AC Output 

GFCI Tripped

.

Reset the GFCI. 

 

Note: This error function is not effective when Load Sense “LdS’ function is in use. 

E14

Display panel has 

communication error

.

Check RJ12 cable connected between the main 
and Display panel.

E15

AC Back Feed

 to Unit AC Output.

Check AC Input and AC Output wiring.

E16

Internal Fault. 

Unit damage

.

Consult Customer Service for assistance.

E17

AC 

Input Current 

withdrawn from the unit is close 

to the set AC Circuit Breaker (Cbr) rating.

Reduce AC load. Check the AC Circuit Breaker 
(Cbr) rating match with the external AC Input 
Source Branch Breaker rating.

E18

AC Input Current drawn by unit is beyond the 

current rating of the transfer switch

. (30A for 

120V model, 16A for 230V model). AC Output 
Switch is switched off.

Reduce  AC  Load  connected  to  unit.  Press  and 
hold ‘

Escape

’ button for 5 seconds to reset AC 

Output Switch to provide AC Output from AC 
Input Source.

E19

Battery temperature

 sensed by BTS is > 60°C. 

Battery charging cycle terminates.

Cool down the battery. Battery charging cycle 
will automatically resume when the temperature 
drops to below 50 °C.

E20

Battery temperature

 sensed by BTS is > 55 °C and 

is close to battery temperature thermal shutdown

Check battery and environmental temperature or 
add ventilation to the battery compartment.

E21

Battery temperature

  sensed  by  BTS  is  <  0  °C. 

Battery charging cycle terminates.

Check battery and environmental temperature. 
The charging cycle will resume when temperature 
increases to > 5 °C. 

Summary of Contents for 61242040





































Reviews:

No comments

Brands by name

Popular brands

Load more brands