manualshive.com logo in svg

Whisper Power 61242040, User Manual

Share
Download
Whisper Power 61242040 User Manual Download Page 19

      

WhisperPower Inverter / Battery Charger

         

19

Load Sense

(Default)

:

 

Continuous AC Output when inverter is ON 

10 : Continuous AC Output when inverter is ON and AC load is > 10W

15 : Continuous AC Output when inverter is ON and AC load is > 15W

20 : Continuous AC Output when inverter is ON and AC load is > 20W

25 : Continuous AC Output when inverter is ON and AC load is > 25W

Battery Low 
Disconnect   

21.0

Battery Low Disconnect Voltage selectable ranges is 21.0 - 24.0V (0.2V steps)

(Default voltage is set to 21.0V)

Battery Low 
Warning

22.0

Battery Low Warning Voltage selectable ranges is 22.0 – 25.0V (0.2V steps)

(Default voltage is set to 22.0V)

Battery Low 
Recovery

24.0

Battery Low Recovery Voltage selectable ranges is 23.0 - 26.0V (0.2V steps)

(Default voltage is set to 24.0V)

Audible 
Buzzer

(Default)

:

 

Buzzer is enabled. Unit buzzes when Warning or Error 

occurs. 

: Buzzer is disabled. Unit does not buzz when Warning and Error occur.

AC Charger

 (Default)

:

 

AC Charger is enabled. Charge battery when AC Input is 

available. 

: AC Charger is disabled. No battery charging when AC Input is available.

Battery Type

(Default)

: GEL Battery, default Bulk Charge/Float Voltage is 28.4V/27.6V 

: AGM Battery, default Bulk Charge/Float Voltage is 28.6V/26.8V

: Flooded Battery, default Bulk Charge/Float Voltage is 28.8V/27.0V

: Lithium Battery, default Bulk Charge/Float Voltage is 27.8V/27.0V

: Program, default Bulk Charge/Float Voltage is 27.6V/26.4V

: Power Supply Mode, Default Power Supply Voltage 27.6V

Bulk Current

50

24V/3000W Models: 

Selectable Ranges 50A, 40A, 30A, 20A, 10A

 

(Default 50A)

24V/2000W Models: 

Selectable Ranges 40A, 30A, 20A, 10A, 5A 

(Default 40A)

.

Bulk/Absorp- 
tion Voltage

  28.4

Bulk/Absorption voltage is based on the battery type chosen. All battery 
types have selectable ranges of 27.6 – 29.6V. 

(Default on GEL Battery is 

28.4V) 

Absorption to 
Float Current

    5

12V/3000W Models

: Selectable Range: 8A, 6A, 5A, 3A, 2A 

 

(Default 5A)

.

12V/2000W Models

: Selectable Range: 6A, 5A, 4A, 3A, 2A  

(Default 4A)

.

Float Voltage

 27.6

Float voltage is based on the battery type chosen. All battery types have 
selectable ranges of 26.0 – 28.0V. 

(Default on GEL Battery is 27.6V)

Recharge 
Voltage

 25.6

Battery Recharge Voltage Selectable Range: 25.6 to 28.0V (0.2V step) 

(Default on GEL, AGM, Flooded, PGM battery setting is 25.6V and Li 
setting is 26.4V)

.

Summary of Contents for 61242040





































Reviews:

No comments

Brands by name

Popular brands

Load more brands