background image

Page 4 | 1-800-343-9463

MPS

 031413

WARRANTY REGISTRATION

installing your system and submit via mail, fax, or e-mail. 

Mail to:

WhisperKOOL

ATTN: Warranty Registration

1738 E. Alpine Avenue 

Stockton, CA 95205-2505

USA

Fax to:

209.466.4606

Scan and email to:

[email protected]

OR

OR

INTRODUCTION

Customer Service

Thank you for purchasing a WhisperKOOL cooling system.  We strive to provide the highest quality products and the 

best possible customer service.  If you have any questions about your system, please call us at 1-800-343-9463 or visit 

WhisperKOOL.com.

Using the Manual

This Owners Manual is intended to assist in the proper maintenance of the cooling system.  In order to ensure the 

longevity of your cooling unit, the equipment should be installed as outlined in the Technician’s Manual. It is also vital 

to establish a proper care and maintenance schedule.  Please read and review this manual carefully and keep it for 

future reference.

What Is the WhisperKOOL Cooling System? 

The WhisperKOOL cooling system is a specialized refrigeration system designed for one purpose only: to maintain 

produces minimal in-cellar noise and has the most lenient exhaust requirements. An exterior housing is required for 

outdoor condensing unit installations.

How Does the Cooling System Work? 

Similar to the air conditioning systems used for homes, the Evaporator Unit (Fan Coil Unit) and Condensing units 

are installed in separate locations and are connected by a refrigerant line set. The evaporator portion is commonly 

installed in the wine cellar, with the condensing unit located either outside or in a remote indoor location that is 

ventilated. An exterior housing is required for outdoor condensing unit installations.

Temperature Setting 

The WhisperKOOL system can be set at any temperature within the acceptable wine-aging range of 45°F to 67°F. It 

is designed to cool up to 55°F cooler than the ambient temperature of the space to which the condensing unit is 

installed.

Summary of Contents for Mini Split





































Reviews: