manualshive.com logo in svg

WHISPER KOOL Mini Split, Tech Manual, Page: 13 / 36

Share
Download
WHISPER KOOL Mini Split Tech Manual Download Page 13

www.whisperkool.com | Page 11

PREPARING AND INSTALLING THE 

EVAPORATOR UNIT (FAN COIL UNIT)

• 

Drill

• 

5/32” Drill Bit

• 

1/4” Socket Drill Bit

• 

1/4”  Wrench

• 

Phillips Head Screwdriver

• 

Tape Measure

• 

Brazing Torch

• 

Drywall Saw

• 

Ladder

• 

Level

• 

Pliers

• 

Pencil

Required Tools:

°

F

1.Detach the Access Panel by removing the 

2. Unscrew the nut attached to the Circular 

Connector (Bottle Probe Input.)

3. Install the Circlar Connector (Bottle Probe 

Input) in The hole located at the bottom of the 

housing.

NOTE:

 From a frontal perspective, the Circular 

Connector is located in the rear-left corner of the 

bottom of the unit.

4. Secure the Circular Connector (Bottle Probe 

Input) to the unit using the provided nut (the 

Rubber Washer should remain inside the unit).

RUBBER WASHER

NUT

UNIT PANEL

CIRCULAR CONNECTOR/ 

BOTTLE PROBE INPUT

HOLE FOR CIRCULAR CONNECTOR 

(BOTTLE PROBE INPUT)

DRAIN PAN

Summary of Contents for Mini Split





































Reviews:

No comments