Whirlpool WRF954CIHB Service Manual Download Page 55

Page: 55 / 59

COMPONENT ACCESS

French-Door Bottom Mount Refrigerator

3-13

Thermistor and Possible Frost Build-Up (Continued)

For Water Valves:

•

On the unit, check the part# of the dual water valve

located behind the water box cover as shown in picture

below:

•

Check the table below and identify the right part# for the

correct water valve and Orion board corresponding to

model# of the unit:

Model

Orion Board

Dual Water Valve

Old Board

New Board

Old Valve

New Valve

WRF992FIF*

W10873533

W10918843

W10853040

W10908836

WRF993FIF*

WRF995FIF*

W10873534

W10918845

KRFC604FS*

W10789117

W10918848

KRFC704F*

JFFCC72EF*

W10789117

W10918848

•

Replace the water valve and Orion board with new part

numbers.

•

Ensure that all the tubes are fully inserted into the water

valve. There is an O-ring inside the valve if the tube is not

fully inserted pass the O-ring it may cause water leak.

•

Ensure the electrical connectors are connected and not

left disconnected as shown below.

•

Before putting the water box cover on, dispense water by

closing the left hand door and observe that there is no

water leaking during the water dispensing.

Water Box Cover

Water Valve Part Number

Location of Orion board
and Part Number label

Bad

Good

Summary of Contents for WRF954CIHB




























































Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands

Whirlpool WRF954CIHB, Service Manual

Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands