Whirlpool WRF954CIHB Service Manual Download Page 49

Page: 49 / 59

COMPONENT ACCESS

French-Door Bottom Mount Refrigerator

3-7

Accessing Refrigerator Compartment Components (Continued)

Freezer Icemaker Fill Tube and Heater

Complete the steps

1-5

from

"Water Filter Bracket and Water

Filter Housing"

instructions.

Remove the water valve cover.

Remove the 1/4" screw at the front of the fill tube cover.

Slide the cover forward to free the rear tabs and remove.

Disconnect the fill tube heater wiring connector located on

the water tank housing, and remove the heater.

NOTE:

During assembly, install the fill tube cover prior to the

water valve cover.

Dual Water Valve and Freezer IM Water Valve

Complete the steps

1-5

from

"Crisper Frame Assembly"

instructions.

Remove the water valve cover.

Disconnect the wiring connector(s).

Remove the ground wire from the valve solenoid frame.

Disconnect the water connections.

Water Reservoir

Complete the steps

1-5

from

"Crisper Frame Assembly"

instructions.

Remove the water valve cover.

Remove the two 1/4" screws at the top of the water tank

housing.

Remove the wire run from the retaining clip.

Remove the two outlet water tubes from the dual water

valve.

Pull the water tank Housing forward and cut the wire tires

holding the water reservoir in place.

Remove the inlet and outlet water connections from the

water reservoir and remove.

Evaporator Cover Assembly

Complete the steps

1-3

from

"Air Tower Cover and Air Filter

LED Light"

instructions.

Complete the steps

1-5

from

"Crisper Frame Assembly"

instructions.

Remove the water valve cover.

Remove the tower cover base.

Remove the four 1/4" screws holding the evaporator cover

assembly in place and work the cover loose.

Compress the pinch clips on the yellow wiring plug at the

bottom right of the cover and push back through the cover.

Unclip the thermistor from the evaporator tubing behind the

top right side of the cover.

Disconnect the two small wiring connectors located behind

the bottom left portion of the cover.

Disconnect the bottom wiring connector extending through

the liner behind the bottom left portion of the evaporator

cover.

Remove the blue tape holding the wiring to the rear of the

cover assembly, feed the wiring through the hole on the left

side of the cover and remove the evaporator cover assembly.

NOTE:

Certain areas of the liner are cut with a laser during

manufacturing. It is normal to see smoke staining on the liner

in these areas.

Water Valve Cover

Summary of Contents for WRF954CIHB




























































Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands

Whirlpool WRF954CIHB, Service Manual

Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands