Whirlpool WRF954CIHB Service Manual Download Page 30

Page: 30 / 59

For Service Technician Use Only

DIAGNOSTICS

1-26

French-Door Bottom Mount Refrigerator

RC Defrost Troubleshooting

Diagnostics has several Service Tests to aid in troubleshooting the RC Defrost system.

Run Service Test 01 - RC Thermistor

•

Ensure the thermistor is not Open “OP” or Shorted “SH”.

Replace any faulty thermistors.

Run Service Test 03 - RC Evaporator Thermistor

•

Ensure the thermistor is not Open “OP” or Shorted “SH”.

Replace any faulty thermistors.

Run Service Test 57 – RC Fan Test

•

Ensure LED Display shows “on”

•

Check that the fan is operating

If fan is not operating:

•

Check all wiring connectors tight (See FIGURE 6, Page 4-6).

•

Check integrity of wiring between control board and fan.

(Continuity or Voltage check as appropriate)

If wiring check indicates bad wiring:

•

Replace wiring harness

If wiring checks OK, or if fan is still not operating:

•

Replace fan.

If LED Display does not show “on”:

•

Replace GF2 Board.

P16-4

Pin 8

16 Pin Conector

12 Pin Conector

Machine Compartment

Left Side

Bottom RightSide

RC Evaporator Area

Fan

3 Pin Fan Conector

Evaporator Cover Assembly

Orion Board

+12.7 VDC

Fan

Power

Supply

P14-3

GF2 Board

Pin 7

in 1

Pin 8

in 2

Controls

Speed

+12.7 VDC

Turns Fan

Pin 3

P14-4

Pin 9

Neutral

Summary of Contents for WRF954CIHB




























































Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands

Whirlpool WRF954CIHB, Service Manual

Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands