Whirlpool WRF954CIHB Service Manual Download Page 31

Page: 31 / 59

For Service Technician Use Only

DIAGNOSTICS

French-Door Bottom Mount Refrigerator

1-27

Moisture Control Heater Troubleshooting

Take resistance reading between GF2 P1-2 and GF2 P2-6.

•

Resistance should be 1400 - 1800 ohms.

•

If the Duct Heater is Open, resistance will read ≈4800 ohms.

•

If the Filter Heater is Open, resistance will read ≈2400 ohms.

If resistance checks are OK:

Run Service Test 65 - Ice Box Duct Heater Test

•

Ensure LED display shows “on”

•

If LED display does not show “on”, replace GF2 board.

If all checks are OK and problems persist:

Run Service Test 88 - Ice Box Air Duct Heater Activation Mode

This will turn the heaters Full On.

•

Use up or down arrow to change activation mode to “01”

•

Press the “Icemaker2” key to confirm selection.

Splice

12 Pin Connector

To RC Liner

P1-2

GF2 Board

Pin 3

Pin 10

WH/BK

115 VAC

WH/BK

Pin 7

Pin 6

P2-6

Neutral

IM Duct Heater

(Cabinet)

Filter

Heater

Pin 9

in 4

Pin 2

Pin 8

4 Pin

Behind

Connector

Water

in RC

Valve Cover

9 Pin

Behind

Connector

Water

in RC

Valve Cover

Pin 3

12 Pin Connector

RC Evaporator Area
Bottom Right in RC

WH/BK

Summary of Contents for WRF954CIHB




























































Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands

Whirlpool WRF954CIHB, Service Manual

Search results

Summary of Contents for WRF954CIHB

Reviews:

Related manuals for WRF954CIHB

Brands by name

Popular brands