Westermo TD-36 Commands Interface Manual Download Page 73 | Manualshive

Page: 73 / 84

background image

6618-3201

73

Short

Form

Long Form

Description

11

CONNECT
4 800

The modem has connected to the line and either line speed
4 800 bit/s., DCE speed reporting is enabled, or the DTE speed
4 800 bit/s, and DTE speed reporting is enabled.

12

CONNECT
9 600

The modem has connected to the line and either line speed
9 600 bit/s., DCE speed reporting is enabled, or the DTE speed
9 600 bit/s, and DTE speed reporting is enabled.

13

CONNECT
7 200

The modem has connected to the line at 7 200 bit/s and DCE speed
reporting is enabled.

14

CONNECT 12
000

The modem has connected to the line at 12 000 bit/s and DCE speed
reporting is enabled.

15

CONNECT
14 400

The modem has connected to the line at 14 400 bit/s and DCE speed
reporting is enabled.

16

CONNECT
19 200

The modem has connected to the line and either line speed
19 200 bit/s., DCE speed reporting is enabled, or the DTE speed
19 200 bit/s, and DTE speed reporting is enabled.

17

CONNECT 38
400

Connection, DTE speed 38 400 bit/s, DTE speed enabled

18

CONNECT 57
600

Connection, DTE speed 57 600 bit/s, DTE speed enabled

19

CONNECT
115 200

Connection, DTE speed 115 200 bit/s, DTE speed enabled

22

CONNECT
75TX/1200RX

The modem has estabilished a V.23 originate connection and line
speed reporting is enabled.

23

CONNECT
1200TX/75RX

The modem has estabilished a V.23 answer connection and line speed
reporting is enabled.

24

DELAYED

For X4, sent when a call fails to connect and the number is
considered “delayed” due to country blacklisting requirements.

32

BLACKLISTED

For X4, sent when a call fails to connect and the number is
considered “blacklisted” due to country blacklisting requirements.

33

FAX

A fax modem connection is estabilished in a facsimile mode.

35

DATA

A data modem connection is estabilished in a facsimile mode.

40

+MRR: 300

The modem has connected to the line at 300 bit/s and carrier
reporting is enabled (see S95 and Xn).

44

+MRR: 1200/75

The V.23 backward channel is detected and carrier reporting is
enabled (see S95 and Xn).

45

+MRR: 75/1200

The V.23 forward channel is detected and carrier reporting is enabled
(see S95 and Xn).

46

+MRR: 1200

The modem has connected to the line at 1200bit/s and carrier
reporting is enabled (see S95 and Xn).

«
...
71
72
73
74
75
...
»

Summary of Contents for TD-36





















































































Reviews:

No comments

Related manuals for TD-36

Brand: Sagem Pages: 4

Brand: RACOM Pages: 19

Brand: Patton electronics Pages: 24

Brand: Ubee Pages: 2

Brand: i-mate Pages: 7

Brand: Black Box Pages: 2

Brand: LOVATO ELECTRIC Pages: 7

Brand: iRZ Pages: 19

BreezeMAX USB 250

Brand: Alvarion Pages: 6

Brand: SEA Pages: 2

Brand: Siemens Pages: 25

Brand: Siemens Pages: 48

Brand: Siemens Pages: 79

Brand: Telecom Pages: 16

Brand: ProSoft Technology Pages: 136

Brand: Proscend Pages: 102

Brand: FiberHome Pages: 78

Brand: DXO Telecom Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands