Wenglor ODX402P0088 Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 23

background image

22

Maintenance Instructions

9. Maintenance Instructions

•  This wenglor Sensor is maintenance-free.
•  It is advisable to clean the lens and the display, and to check the plug connections at regular intervals.
•  Do not clean with solvents or cleansers which could damage the product.

10. Proper Disposal

wenglor sensoric gmbh does not accept the return of unusable or irreparable products. Respectively
valid national waste disposal regulations apply to product disposal.

«
...
20
21
22
23
»

Summary of Contents for ODX402P0088
























Reviews:

No comments

Related manuals for ODX402P0088

Brand: Karella Pages: 20

Brand: paramondo Pages: 44

Brand: Kampmann Pages: 36

Brand: Raven Pages: 70

Brand: Panasonic Pages: 18

Brand: Jabra Pages: 2

Brand: Fenix Pages: 4

Brand: Aroflora Pages: 36

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: Thule Pages: 4

Brand: Sable Pages: 15

Brand: Bison Pages: 3

Brand: Thule Pages: 8

Brand: Aerotech Pages: 58

Brand: Oncam Pages: 2

Carpower CAP-20

Brand: Monacor Pages: 2

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: Manfrotto Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands