WELLTECH WellGate 3511N Technical Manual Download Page 15

Page: 15 / 108

WellGate 3511N Technical Manual EN-V100

Step 5. Start to configure

After enter web management interface, user can see 8 main items.

1. Setup

Wizard:

User can follow steps in wizard to make first-time initial configuration.

2. Operation Mode:

User can setup different modes to LAN and WLAN interface for NAT and bridging

function.

3. Wireless:

User can set all wireless related parameters here.

4. TCP/IP:

User can set LAN and WAN related configurations here.

5. Firewall:

User can set firewall function of WG3511N here.

6. VoIP

Setting:

User can set VoIP related parameters here.

7. Management:

User can check information or manage WG3511N here.

8. System

Reboot:

User can remote reboot WG3511N here.

Button Definition:

Apply Changes

: After change or input any parameter, press this button will save data into WG3511N.

Reset

: Press this button will clean data input by user and restore to original data.

Summary of Contents for WellGate 3511N

































































































Search results

Summary of Contents for WellGate 3511N

Reviews:

Related manuals for WellGate 3511N

Brands by name

Popular brands

WELLTECH WellGate 3511N, Technical Manual

Search results

Summary of Contents for WellGate 3511N

Reviews:

Related manuals for WellGate 3511N

Brands by name

Popular brands