manualshive.com logo in svg

Welbilt Lincoln Impinger 1600 Series, International Service Manual

The Welbilt Lincoln Impinger 1600 Series is an exceptional commercial oven renowned for its reliable performance and precision cooking. Unlock the full potential of this high-quality equipment with the International Service Manual, available for free download at manualshive.com. Discover expert guidance and maximize your culinary skills effortlessly.

Share
Download
background image

Table of Contents

Document #: LIN_GO_SM_IMPLOPRO_S1600_INTL_4605727 – 9/20

Safety Notices .....................................................................................................................2

Definitions.................................................................................................................................................2

Section 1

General Information

Model Number Key ............................................................................................................7

Old Model Numbers ...........................................................................................................7

Section 2

Installation

Exterior Dimension-1600 ..................................................................................................9

Canopy Ventilation Recommendations ..........................................................................10

Installation Requirements ...............................................................................................11

Gas Code Requirements ................................................................................................................... 11

Electrical Code Requirements ......................................................................................................... 11

Spacing Requirements ...................................................................................................................... 12

Ventilation Requirements................................................................................................................. 12

Restraint Requirement – ALL Oven(s) on Casters .................................................................... 13

Installation ........................................................................................................................13

Unloading .............................................................................................................................................. 13

Uncrating ................................................................................................................................................ 14

Manual Gas Valve Installation .........................................................................................14

Assembly Instructions .....................................................................................................14

Section 3

Operation

Sequence of Operation – Impinger Advantage Digital, Gas .........................................19

Power Supply  ....................................................................................................................................... 19

Control Box Auto Cool Down .......................................................................................................... 19

Main Fan Circuit ................................................................................................................................... 19

Burner Circuit ........................................................................................................................................ 19

Temperature Control .......................................................................................................................... 19

Conveyor Drive ..................................................................................................................................... 19

Section 4

Maintenance

Preventative Maintenance ..............................................................................................21

Daily Cleaning ..................................................................................................................21

Weekly Cleaning ...............................................................................................................22

Folding Conveyor Safety .................................................................................................23

Section 5

Troubleshooting

Troubleshooting Guide – Gas Ovens ..............................................................................25

Summary of Contents for Lincoln Impinger 1600 Series





















































Reviews:

No comments

Related manuals for Lincoln Impinger 1600 Series

GE JES737 Owner'S Manual preview
JES737
Brand: GE Pages: 16
GE JVM1635 Owner'S Manual preview
JVM1635
Brand: GE Pages: 36
GE JVM1430 Installation Instructions Manual preview
JVM1430
Brand: GE Pages: 24
GE JNM6171 Owner'S Manual preview
JNM6171
Brand: GE Pages: 60
GE JKP77G Manual preview
JKP77G
Brand: GE Pages: 56
GE JKP86 Installation Instructions Manual preview
JKP86
Brand: GE Pages: 12
GE JKP86 Owner'S Manual preview
JKP86
Brand: GE Pages: 44
GE JES1651 Owner'S Manual preview
JES1651
Brand: GE Pages: 36
GE JES1140 Manual preview
JES1140
Brand: GE Pages: 24
GE JES0738DP Operating Instructions Manual preview
JES0738DP
Brand: GE Pages: 16
GE JES0738 Owner'S Manual preview
JES0738
Brand: GE Pages: 16
GE JES0736 Manual preview
JES0736
Brand: GE Pages: 16
GE JES0736 User Manual preview
JES0736
Brand: GE Pages: 16
GE JNM3161 Owner'S Manual preview
JNM3161
Brand: GE Pages: 56
GE JES1460DN Owner'S Manual preview
JES1460DN
Brand: GE Pages: 36
GE JKP85 Series Owner'S Manual preview
JKP85 Series
Brand: GE Pages: 44
Daewoo KOR-1A5A Operating Instructions Manual preview
KOR-1A5A
Brand: Daewoo Pages: 30
GE JVM6175SFSS Use And Care Manual preview
JVM6175SFSS
Brand: GE Pages: 60

Brands by name

Popular brands

Load more brands